VIBE286 Dimensions: 11.06"W x 2.24"H x 21"L.. (2x) VCHB112 Dimension: 20.8"W x 15"H x 12"..LQ16CAP 3.5"D x 8.86"H.
Get Price
4X90-WATT 4-CHANNEL AMPLIFIER
Get Price
PLA2260 Dimensions: 10.63" (W) x 1.42" (H) x 21" (L).. (2x) PLWCH12D Overall Diameter: 12.6" Mounting Depth: 3.28"..
PLCAPE50 Dimensions: 8.86"H 3.5"W
Get Price
750-WATT CLASS D MONO SUB AMPLIFIER
Get Price
4-Channel Power Density Digital Amplifier, 100 watts x 4 chan @ 2 ohms, Total RMS: 400 watts, Signal-to-Noise Ratio: 76dBA, Switch-Mode Digital Topology, CEA-2006 Compliant Amplifier
Get Price
# J2 Series Monoblock Class D Car Amplifier
# RMS Power Rating:
* 4 ohms: 400 watts x 1 chan.
* 2 ohms: 700 watts x 1 chan.
* 1 ohm: 1000 watts x 1 chan.
# MOSFET power supply
# Remote gain control included
# Power and protection LED indicators
# Single-band adjustable 0-12 dB bass EQ with 45 Hz center frequency
# High-level and low-level (RCA-jack) inputs
# Speaker outputs
# Preamp RCA outputs
# Silver-plated RCA level inputs
# Silver-plated screw terminals
# Input sensitivity can be used to match the unit's output voltage to the input stage of each amplifier channel
# Outer casing is designed to remove heat from the circuitry
# 12dB/octave low-pass active filter
# Variable low-pass filter (40-300 Hz)
# Frequency response: 10-160 Hz
# Dimensions: 14.6"L x 9.6"W x 2.15"H
# 4-gauge power and ground wiring is required for installation. Contact us for information regarding a discount on select amplifier kits when purchased together with this amplifier.
Get Price
ZX-Series amplifier with 400-watt sub channel and 700 watt maximum.
Get Price
Class A/B Four-Channel Full-Range Amplifier *
Absolute Symmetry™ Class A/B Circuit *
Differential-Balanced Input Topology: 2 pair of inputs *
On-board Crossover: Fully-variable (50 Hz - 5 kHz), selectable-slope / mode (12 or 24 dB / octave, LP or HP) for each pair of channels *
Speaker output connections: Accept up to 8 AWG wire *
+12V and Ground connections: Accept up to 4 AWG wire *
Rated Power (4 Channel Mode): 75 W RMS x 4 @ 1.5 ohm-4 ohm (11V-14.5V) *
Rated Power (Bridged to 2 Channel): 150 W RMS x 2 @ 3 ohm-8 ohm (11V-14.5V) *
S/N Ratio: >108.5 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) *
Frequency Response: 5 Hz - 30 kHz (+0, -1dB) *
THD at Rated Power: 200 @ 4 ohm per ch. / 50 Hz; >100 @ 2 ohm per ch. / 50 Hz *
Slew Rate: ±25 V / µS @ 4 ohm per ch. *
Left to Right Channel Separation: >75 dB @ 1 kHz *
Input Range: Switchable from 200mV-2V RMS to 800mV-8V RMS *
Dimensions (L x W x H): 13.40 x 9.25 x 2.36 in.; 340 x 235 x 60 mm
Get Price
4X170-WATT 4-CHANNEL AMPLIFIER
Get Price
VIBE286 Dimensions: 11.06"W x 2.24"H x 21"L
Get Price
Top Search
Last Search
